#600 Primer/Saturant is a low viscosity, high acrylic solids emulsion formulated as
a deterrent to stains and asphalt bleeding. The super adhesion
qualities permit use over most existing roof surfaces after cleaning.#600 Primer/Saturant Roof Coating
DESCRIPTION
#600 Primer/Saturant is a low viscosity, high acrylic solids emulsion formulated
as a deterrent to stains and asphalt bleeding. The super adhesion
qualities permit use over most existing roof surfaces after cleaning.
#600 Primer/Saturant absorbs the fine dust commonly left after power washing or vacuuming roof surfaces. As a surface conditioner it assures a bond to chalky weathered acrylic coatings and loose granules on rolled roofing.
PRODUCT USES
Use as a primer and surface conditioner over the following surfaces
:
Use to apply polyester roofing fabrics to parapets and
entire field areas of the roof prior to application of roof coating. #600
Fabric Saturant is also used to adhere the 4" POL-E-FORCE over the lap
seams and as the first coat over the entire surface of POL-E-BASE.
Light weight polyester fabrics may be used as a cap sheet over existing polyurethane foam roofing by using #600 Fabric Saturant as an adhesive and saturant prior to coating the surface.
SURFACE PREPARATION
The surface must be dry, sound, smooth and clean, free of dirt, oil, grease,
asphalt that is not cured dry, or any contaminate that would adversely
affect adhesion, free of blisters and water ponding. The roof surface must
be properly sloped to drains and eaves. Cants and tapered edges are to be
sound and pre-formed to a 45º angle. Do not apply over wet roof
insulation. If existing roof is not dry or sound, tear it off.
Remove all loose roofing from parapets before applying reinforcing fabric with
#600 Primer/Saturant. Do not apply over asphalt based aluminum or silicone
coatings without applying an oil based primer that will adhere to silicone
coatings.
APPLICATION
For adhering fabric apply at the rate of 80 sq. ft. per gallon. When
used as a primer coat the cleaned area at the rate of 100 sq. ft. per
gallon. Apply with nylon paint brush, paint
roller or paint spray equipment.
PRECAUTIONS
Temperature and humidity affect the curing time. Do not apply at
temperature below 50ºF, or if the temperature will fall below 40ºF within 24
hours. Do not apply if it will rain within 24 hours. Protect the
contents of this container from freezing.
CLEAN-UP
Tools and equipment may be cleaned with water immediately after use. Do
not thin this product.
| Viscosity | 1200>< CPS | ||||||||||||
| Thinning | Thinning of products is not recommended. | ||||||||||||
| Dry Time | Temperature and humidity affect the curing time. Tack time varies from 10 to 15 minutes. Acrylic coating may be applied after 5 hours. | ||||||||||||
| Clean Up | Tools and equipment may be cleaned immediately after used with detergent and water. | ||||||||||||
| Flash Point | Not Determined (aqueous system). | ||||||||||||
| Weight/Gallon | 8.71>< | ||||||||||||
| U.S.D.A. | Approved for walls and ceilings in food processing plants. | ||||||||||||
| Caution | Keep out of reach of children. Close container after each use. Avoid prolonged contact with skin or breathing or spray mist. Do not take internally. Use adequate ventilation. | ||||||||||||
| Packaging |
|
LIMITED WARRANTY
Specification Chemicals, Inc. warrants this product which is designed to
be used by experienced applicators in accordance with industry accepted work
practices. Since we have no control over the design or the workmanship of
the installation, we make no warranties on the performance of the finished
application. We do warrant this product to be free of defects in material
and workmanship for a period of five years. Our sole liability shall be to
supply a like quantity of non-defective product. Specification Chemicals,
Inc. makes no other warranty of any kind, express or implied, in fact or
in law, including without limitation, the warranty of fitness for a particular
purpose, other than the limited warranty set forth above.